MILLFIX™ FIXINGS.

Specifying the correct fixings is critical to the service life of timber cladding. Our fixings ensure long service life for best performance of the timber and coatings in any location. These systems can be written into the NBS H21 specification.

Millfix™ screws and fixings systems

Specifically designed from hardened stainless steel. Features include sharp angled thread for deep anchoring, a scraping groove at the screw tip, milling ribs above the thread and a countersunk head providing clean detailing to your project. The screw design allows fastening close to the edge of boards without the risk of wood splintering and heat treatment gives a 60% higher breaking torque than standard V2A and V4A austenitic stainless steel. We recommend using Millfix™ screws as part of our Millfix™ systems for all profiles.

Millfix TX10 Screws, Secret-fix

  • Specifically designed from hardened stainless steel suitable for a range of locations
  • Designed to allow fastening close to the edge of boards without the risk of wood splintering
  • 60% higher breaking torque than standard V2A and V4A austenitic stainless steel
  • Quick & easy installation, with no pilot hole required
  • Fixing centres required every 400-600mm

Specifications

  • Exterior Timber Cladding
  • Millfix™ 3.2x40mm secret-fix.

  • Suitable for profiles: MW-2 and MW-5.

  • 1000 per Box

  • £130 per Box ex VAT

  • TX10 Driver

Millfix™ TX15 Screws, Face-fix 50MM

  • Hardened stainless steel suitable for a range of locations
  • Quick & easy installation, with no pilot hole required
  • Sharp angled thread for deep anchoring
  • Countersunk head providing clean detailing to your project
  • 60% higher breaking torque than standard V2A and V4A austenitic stainless steel
  • Fixing centres required every 400-600mm

Specifications

  • Exterior Timber Cladding
  • Millfix™ 4.0x50mm face-fix

  • Suitable for all profiles and trim

  • 500 per box

  • £88 per Box ex VAT

  • TX15 Driver

Millfix™ TX15 Screws, Face-fix 70MM

  • Hardened stainless steel suitable for a range of locations
  • Quick & easy installation, with no pilot hole required
  • Sharp angled thread for deep anchoring
  • Countersunk head providing clean detailing to your project
  • 60% higher breaking torque than standard V2A and V4A austenitic stainless steel
  • Fixing centres required every 400-600mm

Specifications

  • Exterior Timber Cladding
  • Millfix™ 4.0x70mm face-fix

  • Suitable for profiles: MW-12 and decking

  • 500 per box

  • £98 per Box ex VAT

  • TX15 Driver

Millfix™ Facade Clip

Millfix™ Facade Clips for profile MW-7, enhances ventilation by creating a free flow of air between the back face of the cladding board and the vertical batten. By secret fixing, the front faces of the cladding boards are left fully intact which improves longevity and makes it ideal for factory coated products.

  • Each facade clip comes supplied with one 4.5 x 29 mm fixing screw with a drill point and two 4.2 x L assembly screws.

Specifications

  • Exterior Timber Cladding
  • Flawless secret-fix

  • Suitable for profile: MW-7 (finished widths 20×68 or 20×93)

  • 300 per Box

  • £250 per Box ex VAT

Millfix™ Ventilation Strip

In addition to fixings, Millfix™ Ventilation Strip is designed to be used on all profiles to compensate for the natural movement of the timber. By creating a gap between timber elements and enhancing ventilation, the pressure on fixings is reduced.

Specifications

  • Millfix™ 9750x10x8mm ventilation strip.

  • Compatible with Millfix™ secret or face-fix screws

  • Suitable for all profiles

  • 10 rolls per unit

  • £200 per unit ex VAT